If you are sourcing hexagonal wire netting for a poultry house, a garden fencing program, or a stucco reinforcement package, the single most important specification decision is not the mesh size or the roll length — it is when the zinc is applied. Galvanized before weaving (GBW) and galvanized after weaving (GAW) look almost identical on a loading dock, yet they behave completely differently after 18 months in the field. One is a low-cost solution for temporary or indoor duty; the other is the only safe choice for permanent outdoor structures.
This guide breaks down the real technical difference between galvanized before vs after weaving hexagonal wire netting, with the coating weights, service lifespans and cost deltas you need to make a defensible specification — written from the factory floor of an ISO 9001 wire mesh manufacturer.
What “Galvanized Before Weaving” (GBW) Actually Means
In the GBW process, low-carbon Q195 steel wire is drawn to gauge, passed through a zinc bath (hot-dip) or electroplating line, and only then fed into the hexagonal mesh loom. Because the zinc layer is already on the wire, the loom twists pre-coated wire into the familiar double-twist hexagonal pattern.
The result is a cost-efficient mesh with a typical zinc coating of 30–60 g/m². It performs well where moisture load is low, but there is one structural weakness every engineer should understand: the mechanical twisting action at each joint can micro-crack the zinc layer, and no zinc ever reaches the freshly cut roll ends.
- Best suited to: poultry and rabbit coop interiors, temporary site fencing, packaging, indoor partition mesh, craft and decorative use.
- Realistic outdoor life: roughly 1–3 years depending on humidity, coastal salt and fertilizer/ammonia exposure.
- Commercial advantage: typically 25–40% cheaper per roll than GAW at the same aperture.
What “Galvanized After Weaving” (GAW) Delivers
GAW reverses the sequence: bare Q195 wire is woven first, then the finished mesh travels through a hot-dip zinc kettle at around 450 °C. Molten zinc wets every wire surface and flows into the twist joints, sealing the points where two wires cross and where the mesh was cut at the roll edge.
Coating weights reach 200–260 g/m² — four to six times the GBW level. That continuous, joint-sealing layer is why GAW hexagonal netting is the default for permanent outdoor enclosures, coastal installations and any project with a warranty period measured in decades.
- Best suited to: poultry farms and free-range operations, predator-proof garden fencing, coastal and high-humidity sites, agricultural pens with manure/ammonia load.
- Realistic outdoor life: 10–15+ years with intact coating; longer in inland temperate climates.
- Trade-off: higher unit price and slightly less dimensional precision at the joints than GBW.
Galvanized Before vs After Weaving: Side-by-Side Specifications
The table below reflects our standard production range for hexagonal wire mesh (chicken wire & rabbit netting). Use it as a specification baseline when you draft your BOQ or send an RFQ.
| Parameter | Standard Specification | Custom Factory Option |
|---|---|---|
| Base Wire Material | Q195 low-carbon steel wire | Q235 / high-tensile wire on request |
| Wire Gauge | BWG 14–22 (0.7 mm – 2.0 mm) | 0.6 mm – 2.5 mm |
| Mesh Aperture | 1/2″ – 2″ (13 mm – 50 mm) | 3/8″ – 3″ (10 mm – 75 mm) |
| Zinc Coating (GBW) | 30–60 g/m², electro or hot-dipped before weaving | Up to 80 g/m² |
| Zinc Coating (GAW) | 200–260 g/m², hot-dipped after weaving, joints sealed | Up to 280 g/m² heavy coating |
| Salt Spray Resistance (ASTM B117) | GBW ≈ 48–96 h / GAW ≈ 500 h+ | Third-party test report available |
| Roll Size | 0.9 m × 25 m, 1 m × 30 m | Custom width 0.5–2 m, length to 50 m |
| Indicative Outdoor Lifespan | GBW 1–3 years / GAW 10–15+ years | PVC-coated option for 20+ years |
| Quality System | ISO 9001 factory direct supply | Mill test certificate per batch |
Which One Should You Specify?
Poultry, Rabbit and Chicken Coop Builders
Bird manure releases ammonia and hydrogen sulphide that attack zinc quickly, and coop interiors stay humid year-round. For a permanent house, specify GAW at 240 g/m² minimum. Reserve GBW strictly for brooder pens, temporary quarantine cages, or suspended cage floors where the mesh is replaced on a short cycle.
Garden Fencing Wholesalers
This is where a two-tier catalogue pays off. Stock GBW in BWG 20–22 with 1″ aperture for the DIY/budget shelf, and GAW in BWG 16–18 with 1/2″–1″ aperture for predator-proof and coastal garden projects. The GAW line carries a measurable warranty story — “15-year rust-through guarantee” — which converts far better at retail than a vague “galvanized” claim.
Plastering and Stucco Reinforcement Contractors
Mesh embedded in mortar is protected from direct weathering but exposed at laps, corners and cut edges. Choose GAW with a tight, uniform coating so the mortar keys mechanically into the hexagonal apertures without thick zinc nodules causing humps. BWG 18–20 with 1″ aperture is the standard workhorse; confirm coating adhesion, not just coating weight. You can review our full hexagonal wire netting specification range for aperture-to-gauge combinations.
How Wanson Steel & Wire Mesh Controls Quality
As an ISO 9001 certified manufacturer, we control every stage in-house: wire drawing from Q195 rod, zinc weight verification by stripping test per batch, loom tension monitoring for consistent hexagonal geometry, and roll-end sealing checks before packing. Every export order ships with a mill test certificate stating wire gauge, aperture tolerance, zinc coating weight and tensile strength.
- Aperture tolerance held at ±5% for uniform mortar keying and clean panel alignment.
- Zinc weight sampled from the head, middle and tail of each production run.
- Compressed, moisture-barrier roll packing for sea freight to North America, Europe and Australia.
- Full range available at our hexagonal wire mesh product page.
Ordering Checklist for Contractors and Wholesalers
When you issue an RFQ, state these five points and you will eliminate 90% of supplier disputes: (1) galvanizing method — GBW or GAW; (2) zinc coating weight in g/m², not just “hot-dipped”; (3) wire gauge in BWG and millimetres; (4) aperture and roll dimensions; (5) packing method and container loading preference. Suppliers who can answer all five in writing within 24 hours are the ones who actually control their process.
Need Factory-Direct Pricing for Your Project?
Send your drawings or Bill of Quantities (BOQ) to Wanson Steel & Wire Mesh for a fast, competitive quote within 24 hours.
📧 Email: sales@chinasteelmesh.com | 💬 WhatsApp: +86 199 3221 9476

